Industrial Millwright & Conveyor Servicesin Joliet, Illinois
Quick overview
SSI serves the Joliet area from our Portage, Indiana shop, about 58 miles and 65 minutes west on I-80. Our crews install and repair conveyor systems, service scales and load cells, balance fans, weld on site and run preventive maintenance for Will County distribution, chemical, refining and power operations.
Joliet at a glance
- Approx. drive from Portage
- ~65 min
- Approx. road miles
- 58 mi
- Prequalified contractor
- ISN & Avetta
Calls we get
What we're called for in Joliet
Sortation drive failing before peak
A distribution center calls when a conveyor drive starts running hot or a take-up keeps slipping weeks before peak season. We replace or rebuild the drive in phases that fit your slow shifts.
Conveyor SystemsRail-car weigh hopper drifting
A rail-served plant sees a weigh hopper fail calibration again. We check load cells, mounts and the structure around them, since a bent bracket or bound flexure often looks like an electrical fault.
Scales & Load CellsExhaust fan shaking on the river
A chemical or power site along the river reports rising vibration on an exhaust or scrubber fan. We measure it, clean or correct the wheel, and balance it in place to get it back inside limits.
Fan Rebuilds & BalancingNew motor, same old bearing failures
A plant swaps a pump or conveyor motor and the bearings fail again within months. We laser align the coupling, correct soft foot, and leave a written report of the final readings.
Laser Shaft Alignment
From the Portage shop
How we get to Joliet
The route
Crews take I-94 and the Borman west from Portage, stay on I-80 where it splits off near the state line, and run straight across the south suburbs into Joliet. Sites near I-55 are a short hop north from there.
The local industrial base
Will County is one of the largest rail and logistics hubs in the country, with intermodal yards and big distribution buildings along I-80 and I-55. The river corridor adds refining, chemical and power operations. That mix means miles of conveyor that cannot stop, plus heavy process equipment under strict site rules.
Breakdown in Joliet? (219) 386-1506 is answered 24/7.
Map data © OpenStreetMap contributors
About 65 minutes
Roughly 58 miles west on I-80.
Material handling
Conveyor installs, drive rebuilds and repairs.
Scales
Load cell and weigh hopper service.
24/7 line
(219) 386-1506 for breakdowns.
What we do here
Services in Joliet
Conveyor Systems
Conveyor installs, repairs, drives, pulleys and tracking.
Scales & Load Cells
Load cell install, troubleshooting and replacement.
Fan Rebuilds & Balancing
Fans balanced in place or in the shop, rebuilt and aligned.
Laser Shaft Alignment
Aligned to spec, with a written report.
On-Site & Specialty Welding
Mobile welding rigs at your plant, 24/7 for emergencies.
24/7 Emergency Repair
Line down? Call (219) 386-1506, day or night.
Preventive Maintenance
Inspections, alignment and outage plans that cut breakdowns.
Millwright Services
Rigging, setting, alignment, installs and outage work.
Industries near Joliet
Nearby service areas
Have a job in Joliet?
Send the equipment, the plant address and what you're seeing. A crew lead calls back with timing and next steps.
Why does Joliet work lean toward conveyors and scales?
Joliet work leans that way because Will County moves freight. Intermodal yards and distribution buildings run long conveyor lines, sorters and dock gear. Rail-served plants weigh what comes in and goes out. When a drive or a load cell fails here, product stops moving, so most of our calls start on the material handling side.
The river corridor adds a second kind of job: fans, pumps and environmental equipment at chemical, refining and power sites.
Is a 65-minute drive too far for a Joliet plant?
No, for most work it isn’t. Conveyor projects, PM programs and outages are scheduled weeks ahead, so the drive is a small part of the job. We pre-fabricate in Portage and show up with parts staged. For a breakdown, our 24/7 line gives you a straight estimate instead of a promise we can’t keep.
How the distance usually plays out:
| Type of job | How we handle the distance |
|---|---|
| Conveyor install or extension | Shop-built supports and guards, staged before day 1 |
| Drive or gearbox failure | Rebuild in our shop, or swap a spare we rebuilt earlier |
| Scale drifting | Planned visit with load cells and mounts on the truck |
| Line down | Emergency repair crew with welding and rigging gear |
What keeps a Joliet conveyor system running through peak season?
A short list of habits keeps it running. Most failures we see trace back to drives, alignment and take-ups that were never checked between peaks. A preventive maintenance route catches them while you still have slack in the schedule to fix them.
- check drive temperatures and gearbox oil before peak, not during it;
- laser align motors after every replacement;
- keep one rebuilt spare for the drives you can’t run without;
- repair cracked frames and chute liners with on-site welding instead of waiting on new steel.
Our conveyor systems page covers the full scope.
Which Joliet sites need fan balancing and environmental work?
Chemical, refining and power sites along the river need it most. Their exhaust, scrubber and collector fans run in dirty air, collect buildup and lose balance. Fan balancing on site brings vibration back down without pulling the wheel. See our chemical processing and power generation pages.
Farther south, our Kankakee page covers that area. Call (219) 386-1506 or request a quote.
Local questions
Joliet FAQs
How far is SSI from Joliet?
Our Portage shop is roughly 58 miles from Joliet, about 65 minutes in normal traffic along I-80. That makes planned work like conveyor projects, PM visits and outages a good fit. For breakdowns, call (219) 386-1506 and we will tell you honestly when a crew can be on site, rather than quote a guaranteed time.
Do you work on conveyors in Joliet-area distribution centers?
Yes. We install, extend, rebuild and repair conveyor systems, including drives, take-ups, rollers, belts and supports. We fabricate custom chutes, guards and platforms in our shop. Work is planned around shift changes and peak seasons, and we can rebuild a spare drive ahead of time so a failure becomes a swap.
Can SSI handle an emergency repair in Joliet?
Yes. Our 24/7 line takes breakdown calls from Will County the same as anywhere else. Tell us what failed and where, and we give you a realistic arrival estimate. Crews arrive with welding and rigging gear, and our Portage machine shop can make or repair parts while the crew works on site.
Do you follow refinery and chemical site safety rules?
Yes. We work inside your permit system, with lockout/tagout, hot work, confined space and fall protection programs. Every job starts with a job hazard analysis, and we carry ISNetworld membership and Avetta prequalification, which many Will County process sites require before a contractor can badge in.
Request service in Joliet
Tell us what's running rough. We'll tell you how fast we can be there.